亚洲三区在线观看无套内射,日韩欧美电影91网,这里有国产视频,超级碰不卡视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

self-locking hydraulic cylinder Sold to The Philippines

Release time:2023-11-12 15:27:17 Hits: Current position: Home > News

This article mainly introduces:

The Philippines hydraulic cylinder,self-locking hydraulic cylinder manufacturer,self-locking hydraulic cylinder

The Philippines self-locking hydraulic cylinder

(The Philippines self-locking hydraulic cylinder,produced by Hengyu Group)

self-locking hydraulic cylinder are widely used in The Philippines,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed self-locking hydraulic cylinder for customers from The Philippines.

Introduction to self-locking hydraulic cylinder:

The repair method of self-locking hydraulic cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

The body of the self-locking hydraulic cylinder on the processing process requirements: the body of the self-locking hydraulic cylinder is an important and essential part of the self-locking hydraulic cylinder, because it has an irreplaceable role. The processing requirements for this part are very high, requiring that the surface roughness of the self-locking hydraulic cylinder after processing should reach 0.4-0.8um, and the coaxiality and wear resistance requirements are also very high.

In use, the self-locking hydraulic cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the self-locking hydraulic cylinder.

When the self-locking hydraulic cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

Answers to some questions about self-locking hydraulic cylinder:

What should we pay attention to when using the cylinder?
When using the cylinder, we should pay attention to the environment and temperature in which it is located as follows: 1. Before working, the hydraulic cylinder must carry out several reciprocating movements under low pressure (greater than the starting pressure), and work normally after removing the gas in the cylinder. 2. Precautions when removing the hydraulic cylinder: ① The pressure in the hydraulic circuit is reduced to zero before disassembly. ② The screw thread at the top of the piston rod should be prevented from damage when disassembling. ③ Due to the different structure and size of the hydraulic cylinder, the order of disassembly is also slightly different. Generally, the fastening bolt of the end cover should be loosened first. Internal card chain card key application special tools.

What are the connection methods of the hydraulic cylinder? The connection modes of the cylinder and the actuator are earring connection, hinge shaft connection, thread connection, etc. The connection modes of tubing and cylinder are threaded connection, flange connection, etc.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产 麻豆 一区| 成人网站在线播放一区| 制服诱惑不卡91| 最新久久久久亚洲AV无码专区体验| 抽插后入中文字幕| 小黄人官网成人| 日韩av干屁股| 亚洲AV六区| 欧美视频一区视频二区| 午夜自慰福利| 啊啊啊我的舒服在线视频| 人人澡人人妻人人AV| 色婷婷五月基地在线| 色AV色色色A色A色A色A| 久久中文字幕无码爆| 亚洲a∨国产av综合av麻豆丫| 嗯嗯网站在线观看免费黄| 国产无码操逼逼| 欧美日韩二区后进| 久久和日本| 少妇口爆三区| 天天日天天操天天射天天干| 香蕉成人久久| 骚逼操的好爽| 麻豆传媒综合在线观看| 大香蕉久久加勒比| av后入av| 曰韩欧美成人在线看线| 欧美拍偷拍网一区二区| 日本猛插精品久久| 国产视频第9页| 国产欧美偷拍自拍| 亚洲欧美黄色成人网站在线观看| 小黄片一区二区三欧美| 主播精品国產| 后入 一区二区| 九一区一区二区三区| 亚洲欧美一区二区图片| 久久欧美三级片| 国产精品久久久久久久黑人 | 国产欧美日韩无线看|