亚洲三区在线观看无套内射,日韩欧美电影91网,这里有国产视频,超级碰不卡视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

series synchronous cylinder Sold to Nepal

Release time:2023-11-12 15:27:27 Hits: Current position: Home > News

This article mainly introduces:

Nepal hydraulic cylinder,series synchronous cylinder manufacturer,series synchronous cylinder

Nepal series synchronous cylinder

(Nepal series synchronous cylinder,produced by Hengyu Hydraulic Co., Ltd)

series synchronous cylinder are widely used in Nepal,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed series synchronous cylinder for customers from Nepal.

Introduction to series synchronous cylinder:

When the series synchronous cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

If the series synchronous cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the series synchronous cylinder. The internal parts of the series synchronous cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the series synchronous cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the series synchronous cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the series synchronous cylinder bore processing is out of whack. Because the piston and series synchronous cylinder, guide rail and piston rod are relative If the series synchronous cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling series synchronous cylinder weight composition and calculation. The weight of the series synchronous cylinder is composed of the series synchronous cylinder diameter, the outer diameter and weight of the series synchronous cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

Do not regularly check the damage of the chrome layer of the series synchronous cylinder: completely extend the series synchronous cylinder and carefully check whether there is any surface damage such as injury, strain, welding slag, such as the surface damage position, in the series synchronous cylinder block < 20cm, and the damage depth < 5mm, should be repaired in time to prevent long-term damage to the series synchronous cylinder seal. Welding slag is strictly prohibited on the surface of the series synchronous cylinder.

The repair method of the series synchronous cylinder: the repair of the series synchronous cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

Answers to some questions about series synchronous cylinder:

How many tons is the oil cylinder 16mpa?
It depends on the cross-sectional area of the cylinder A(mm2)F=16mpa×A unit is (tons).

What is the thin cylinder used for?
The principle is no different from ordinary cylinders, that is, the installation space is small, the formation is small, and it is suitable for some special occasions. For example, the space is compact and the place of small travel is used.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
色婷婷久久久精品中文| 超碰AV四虎| 久久99国产精一区二区三无码| 少妇性生活免费视频| 国产日韩欧美亚| 日韩精品第一做| 巨臀大屁股熟妇一区二区三区电影| 欧美一区二区三区夕月| 国产性欧美一区二区| 丁香国产精品视频一区二区三区| 男人色天堂av| 人妻视频不卡高清视频| 操欧美老女人逼视频| 97资源在线播放| 我要看91视频黄色的| 97色伦合综合在线视频观看| 福利地址一区| 舔大师一区二区| 日本 久久久久久| 国产一区 日韩| 日本中文不卡二区| 色吧成人综合网| 伊人久久 99| 中国少妇一级免费黄色电影| 老司机视频手机在线观看网址| 亚洲在线偷拍自拍一区| 狠狠入美女| 久热青青视频| 亚洲另类图区一区| 在线观看欧美一区二区| 日本少妇的激情在线观看| 亚洲综合人成视频| 国产网战无遮档| 欧美日韩精品www.| 国产精品日韩无码| 少妇脚交视频| 天天干天天做天天日| 久色婷婷xxxx| 三级黄片亚洲| 久久久久久囯| 国产精品插插久久久久|