亚洲三区在线观看无套内射,日韩欧美电影91网,这里有国产视频,超级碰不卡视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tilting furnace hydraulic cylinder Sold to Turkmenistan

Release time:2023-11-19 14:07:00 Hits: Current position: Home > News

This article mainly introduces:

Turkmenistan hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

Turkmenistan tilting furnace hydraulic cylinder

(Turkmenistan tilting furnace hydraulic cylinder,produced by Hebei Hengyu company)

tilting furnace hydraulic cylinder are widely used in Turkmenistan,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed tilting furnace hydraulic cylinder for customers from Turkmenistan.

Introduction to tilting furnace hydraulic cylinder:

Improve the service life of the tilting furnace hydraulic cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the tilting furnace hydraulic cylinder (such as the tilting furnace hydraulic cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the tilting furnace hydraulic cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the tilting furnace hydraulic cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single tilting furnace hydraulic cylinder exhaust.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the tilting furnace hydraulic cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

Analysis of commonly used seals: The wear ring and slip ring commonly used on the tilting furnace hydraulic cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

Repair method of small range wear of oil tilting furnace hydraulic cylinder: 1. Use oxygen-acetylene flame to bake the scratched part (master the temperature, avoid surface annealing), bake the oil on the metal surface all the year round until no sparks splash; 2. The scratched part is treated with an Angle grinder, the grinding depth is more than 1 mm, and the groove is polished along the guide rail, preferably a dovetail groove. Scratch both ends of the drilling deeper, change the force situation; 3. Clean the surface with absorbent cotton dipped in acetone or anhydrous ethanol.

Answers to some questions about tilting furnace hydraulic cylinder:

How to calculate the tonnage of the hydraulic press? Example: The input cylinder pressure is 5Mpa, the end area of the cylinder piston is 100mm, and how much is the thrust tonnage?
F=P*S=5*10^6*3.14*(1/20)^2=39250N.

Design a hydraulic cylinder, the inner diameter of the cylinder is 100mm, what size of piston rod is best used?
This involves how much speed ratio you need, that is, the area ratio of the rod cavity and the rodless cavity, if the weight is relatively large, it is recommended that the speed ratio choose 2, that is, the piston rod diameter choose 70mm, under normal circumstances, the speed ratio choose 1.46, the piston rod diameter choose 55mm. Of course, there are many factors that affect the diameter of the piston rod, such as stroke, stroke is too long, in order to stabilize the work of the hydraulic cylinder, its diameter also needs to choose a relatively large, sometimes even non-standard products, need to choose according to the actual situation.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
人人操天天摞| 国产精品一级二级网站| 国产美国日本欧美一区二区三区| 亚洲日韩婷婷| 久久视频 这里只有精品| 亚洲毛片免费观看高清完| 亚洲天堂无码av| 亚洲精品天堂在线地址| 少妇后插内射96xxxx| 日韩性交猛干| 日韩人妻少妇一区二区三区三级片| 啊啊,用力草我| 久久久国产天堂| 天天操夜夜性| 中文字幕四季在线不卡视频| 日韩中文字| 日韩区欧美区在线影院| 少妇熟女人妻体内| 国产高潮麻豆| 人妻熟女第3页| 久久成人视频小说| 精99999| 欧美日韩精品色图在线观看| 欧美rA一区二区| 日韩一二三AV| 天天摸天天添天天日| 强伦女教师一区二区三区免费观看| 亚洲欧美狠狠色| 操日本小孩逼逼视频看看| 夜夜草二三四区| 91精品网站白嫩美女| 久久国产一区二区三区欧美日韩| 日本三级片久久久久久| 极品日精品HD| 美女久久久一个人| 亚欧无码在线视频观看| 日韩国产一二三区| 国产亚洲欧美精品久久久久| 人妻虏中文字幕| 大香蕉五月伊人丁香| 国产精品视频熟|