亚洲三区在线观看无套内射,日韩欧美电影91网,这里有国产视频,超级碰不卡视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to Nepal

Release time:2023-11-08 10:36:36 Hits: Current position: Home > News

This article mainly introduces:

Nepal hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

Nepal trunnion cylinder

(Nepal trunnion cylinder,produced by Hengyu Hydraulic Cylinder Factory)

trunnion cylinder are widely used in Nepal,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed trunnion cylinder for customers from Nepal.

Introduction to trunnion cylinder:

When the trunnion cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the trunnion cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil trunnion cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical trunnion cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the trunnion cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

When the hydraulic oil is not pumped into the trunnion cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the trunnion cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

The trunnion cylinder should not be mixed with foreign objects during assembly, which will cause scars. Before the total assembly of the trunnion cylinder, all parts must be fully removed and cleaned. When the parts are installed with burrs or dirt, foreign objects are easily embedded into the surface of the trunnion cylinder wall due to the stiffness and the weight of the parts, causing scars.

When purchasing the trunnion cylinder, try to clarify the following parameters of the trunnion cylinder: A. trunnion cylinder diameter, rod diameter, stroke; B. Working pressure or trunnion cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right trunnion cylinder type can be found accurately and quickly.

Answers to some questions about trunnion cylinder:

How to judge the leakage in the cylinder?
Common judgment method: In the production site, people make full use of watching, listening, smelling, touching and other sensory ways, by observing that the cylinder can not move or delay the action or feel the oil temperature change, vibration and noise, etc., and then judge whether the cylinder has internal leakage according to experience. Another method commonly used in the field is to extend the cylinder in place to ensure that the cylinder does not have any load and will not retract (to prevent the cylinder from internal leakage accidents), turn off the machine, and then remove the tubing with the rod cavity, and then press the switch that pulls out the cylinder (do not press the wrong switch). If the oil nozzle with the rod cavity drains the cylinder internally, If there's no oil coming out, you have to think about something else going wrong.

Why does the tipping bucket cylinder have a cylinder withdrawal problem?
This problem may have a certain relationship with the operation of the driver, the main reasons are the following two situation analysis: 1, the current domestic loader working device is mostly a six-link mechanism, the six-link mechanism in the bucket to the limit position, lift the boom, the rotating bucket cylinder will appear "cylinder pulling" phenomenon, that is, the piston rod of the rotating bucket cylinder will be pulled out. In this case, in order to protect the cylinder, a pressure overload protection valve with large and small cavities is provided on the multi-way valve rotating bucket link (large chamber 18MPa, small chamber 12MPa). 2, before the cylinder is assembled to the whole machine, the cylinder is not limited, the piston rod of the cylinder can be pulled in place before and after, but when it is installed on the whole machine, in order to avoid the cylinder pulling out, the limit switch is installed according to the regulations.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产精品日韩视频欧美精品| 一级黄色透女视频| 三八一区二区三区Av| 国产精品久久码一区二区三区| 日韩精品欧美亚洲蜜乳| 亚洲无码强姦电影天堂| 国产盗摄像头精品区| 人人澡人人妻人| 非洲大鸡吧操逼网| 三级人妻制服诱惑片| 玖玖精品国产精玖玖玖玖| 超碰 人气在线 大香蕉| 色情黄色综合网| 一线欧美爱亚洲| 日本女人和拘一区二区| 国产偷拍v自拍| 成成人超碰p0RN| 成人片大香蕉VCMB| 久综合久久综合久久综合88| 亚洲大尺度无码视频在线| 亚洲精品一三三三菠萝蜜| 中山穗香AV五十路二区| 91深夜无码| 一区=区黄片| 欧美月婷婷激情社区| 欧美大屌内射MMMMM网| 91人妻午夜| 熟妇日熟女| 骚逼真爽视频| 福利精品在线视频网站| 麻豆综合久久| 日本一区国产| 蜜臀综合一综合二| 在线不下载日B免费视频| 国产95在线欧美一区二区乱子伦| 欧美麻豆精品免费专区一区二区三区| 毛片,亚州在线| 欧美噜噜久久久XXX成人高潮| 丝袜美腿AV在线| 日一二三视频| 在线无码无|