亚洲三区在线观看无套内射,日韩欧美电影91网,这里有国产视频,超级碰不卡视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

self-locking hydraulic cylinder Sold to Puerto Rico

Release time:2023-11-08 10:36:38 Hits: Current position: Home > News

This article mainly introduces:

Puerto Rico hydraulic cylinder,self-locking hydraulic cylinder manufacturer,self-locking hydraulic cylinder

Puerto Rico self-locking hydraulic cylinder

(Puerto Rico self-locking hydraulic cylinder,produced by Hebei Hengyu company)

self-locking hydraulic cylinder are widely used in Puerto Rico,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed self-locking hydraulic cylinder for customers from Puerto Rico.

Introduction to self-locking hydraulic cylinder:

The viscosity of the working oil used in the self-locking hydraulic cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

Most of the failure of the self-locking hydraulic cylinder is because there is a foreign body in the self-locking hydraulic cylinder into the failure of the self-locking hydraulic cylinder, the most problematic is that it is difficult to determine when the foreign body is into the self-locking hydraulic cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

If the self-locking hydraulic cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

The coordination of the sliding parts of the self-locking hydraulic cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

Answers to some questions about self-locking hydraulic cylinder:

How to deal with oil cylinder leakage?
The causes of oil leakage and treatment methods are as follows: (1) The spool is stuck or the valve hole is blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check valve body for wear. (2) The piston rod and cylinder are stuck or the hydraulic cylinder is blocked. At this time, no matter how to operate, the hydraulic cylinder does not move or moves very little. At this time, it should be checked whether the piston and piston rod seal is too tight, whether it enters the dirt and colloid precipitate: whether the shaft line of the piston rod and the cylinder is in alignment, and whether the wearing parts and seals are invalid.

Why the injection cylinder retreating after the injection molding machine is started?
It is likely that the projected area of the molded plastic parts is large or the injection pressure set is relatively large, resulting in the expansion force exceeding the clamping force of the injection molding machine, so the mold is backward. You can do the following attempts: 1, reduce the injection force of the injection molding machine; 2, if the injection molding part can not be well formed by reducing the injection force, it is recommended to install the mold to a larger injection molding machine.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲成人7777在线在线播放| 男女亲热| 国产精品999久| 久久B爱B视频| 麻豆91中文字幕在线| 国产 亚洲 探花| 在线熟女人妻av| 黄片区一区| 熟妇人妻中文av无| 黄片久久精品| 美日AV一区在线| 久久三级免费看| 中国极品少妇XXXXX| 日日日色婷婷一区二区| 欧美日韩双插| 裸体女生欧美日本啪啪一区二区三区| pornfree欧美一区二区| 无毒不卡秒播av| 日韩熟女熟妇男人的天堂| 国产1区2区自拍在线观看| 外国欧美日韩黄色电影| 国产精品99久久免费黑人| 香蕉成人黄色电影| 国产又色又爽无遮挡免费动态图| 亚洲中文网一区二区| 日本素人自拍不卡| PoRn 亚洲| 亚洲女同毛片一区二区三区| 一本道欧美xxx| 欧美干免费看| 熟女人妻一区视频免费观看| 大吊狂操美女逼逼网站| 大大香蕉之大大香蕉在线视频| 大香蕉伊人在线成人视频| 成人网站精品国产1区| 日本少妇高潮丝袜高潮在线观看 | 天天操天天干天天插| 国产亚洲日韩欧美色图| porn精品一区| 九99免费黄色片| 欧美成人福利一级视频|