亚洲三区在线观看无套内射,日韩欧美电影91网,这里有国产视频,超级碰不卡视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

forklift steering cylinder Sold to Colombia

Release time:2023-11-28 10:55:11 Hits: Current position: Home > News

This article mainly introduces:

Colombia hydraulic cylinder,forklift steering cylinder manufacturer,forklift steering cylinder

Colombia forklift steering cylinder

(Colombia forklift steering cylinder,produced by Hengyu Hydraulic Cylinder Factory)

forklift steering cylinder are widely used in Colombia,because of long service life,smooth movement,high work efficiency.So our company has designed forklift steering cylinder for customers from Colombia.

Introduction to forklift steering cylinder:

The machining accuracy of the forklift steering cylinder depends on the level of equipment, production technology and testing means. forklift steering cylinder processing methods are commonly used in two ways, one is rough boring - fine boring - rolling, generally with 45# seamless steel pipe, this method of processing quality is good, but the cost is high. Another method is to use 20# cold-drawn seamless steel pipe, and then honing, the cost is lower. The piston rod must be adjusted and straightened before processing, and the coating thickness of the piston rod is generally not less than 0.03mm. The piston must be machined in strict accordance with the groove size and tolerance requirements given in the seal manual.

The assembly work of the forklift steering cylinder has a great impact on the quality of the forklift steering cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

Most of the failure of the forklift steering cylinder is because there is a foreign body in the forklift steering cylinder into the failure of the forklift steering cylinder, the most problematic is that it is difficult to determine when the foreign body is into the forklift steering cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

forklift steering cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

Answers to some questions about forklift steering cylinder:

What are the causes of hydraulic cylinder oil leakage?
First, between the piston rod and the guide sleeve: 1, the cylinder force is not good, there is a radial force between the piston rod and the guide sleeve there is a partial load, so that the oil seal is worn early, causing oil leakage. 2. The ambient temperature of the piston rod is high, especially radiant heat, and the oil seal aging is fast. 3. Whether the oil seal is selected correctly; Check whether the oil seal is damaged during installation. 4, guide sleeve and piston rod matching tolerance is correct. Second, between guide sleeve and cylinder: 1. Whether the O-ring on the guide sleeve is installed correctly, pay special attention to the O-ring can not "roll", especially some O-rings are die-pressed with a die-closing line. Third, common problems: 1, guide sleeve, cylinder, piston rod concentricity is poor. Fit tolerance is correct.

The inner diameter of the injection cylinder is 203.2mm and the diameter of the screw is 63.5mm. What is the enhancement ratio?
Oil pressure multiplied by the cross-sectional area of the cylinder is equal to the theoretical output force value, and then multiplied by the efficiency of the cylinder is equal to the actual output force value, and the oil pressure can be calculated by inverting the value input.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
快操啊视频| 日韩综合激情一区二区三区中文字幕| 每日更新AV高清不卡在线观看| 国内免费av一区二区| 国产一区二区三区爽爽爽| 午夜电影久久久| 大鸡巴狠狠操夜夜操| 日韩免费蜜臀AV| 天天鲁天天爽天天澡| 一区二区月韩| 91式后入少妇爽| 午夜的AV福利| 和一个少妇做就是爽91| 欧美一级久久久黑人| 日本天天爽天天做天天要| 亚洲国产精品久久久久中文午夜| 98人人操人人摸夜夜嗨| 国产成人56.4adm| 啊啊啊肏屄视频| 交换操美女视频| 青青草国产成人AV片app下载| 一区二区三区95| 国产麻豆传媒黄色电影| 69av精品人妻内射影院| 色呦呦免费在线| 色午夜AV男人的天堂久久| 99日本操逼| 欧美天堂最新在线| 熟女日本二区| 久草麻豆一区二区国产| 国产激情偷拍在线| 国产自慰福利在线| 老湿机·COM| 国产在线无码精品欧美| 色呦呦无码精品| 亚洲国产激情不卡2025| 自拍区偷拍区欧美区| 欧美综合在线激情专区| 九九九色| 欧美日韩草在线视频| 色性爱区综合网|