亚洲三区在线观看无套内射,日韩欧美电影91网,这里有国产视频,超级碰不卡视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tension cylinder Sold to Saudi Arabia

Release time:2023-11-08 10:36:47 Hits: Current position: Home > News

This article mainly introduces:

Saudi Arabia hydraulic cylinder,tension cylinder manufacturer,tension cylinder

Saudi Arabia tension cylinder

(Saudi Arabia tension cylinder,produced by Hengyu Group)

tension cylinder are widely used in Saudi Arabia,because of clever hydraulic energy conversion,excellent temperature resistance,high work efficiency.So our company has designed tension cylinder for customers from Saudi Arabia.

Introduction to tension cylinder:

The tension cylinder should be used correctly and maintained regularly. The tension cylinder should be deflated before use, the buffer regulating valve should be adjusted to a reasonable position, the cleanliness of the oil should be checked regularly, the dust on the tension cylinder should be cleaned regularly, and attention should be paid to waterproof and fireproof.

If it is found that the tension cylinder lubrication is poor or the tension cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the tension cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the tension cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the tension cylinder center line. In this way, when the piston works in the tension cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the tension cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

The difference between the integral tension cylinder and the split tension cylinder: The integral tension cylinder and the split tension cylinder in the tension cylinder are two different tension cylinders, and they are very different. The whole tension cylinder, which is cast in one body, is not prone to problems such as oil leakage; The split tension cylinder is welded twice, so if it is not handled well at the welding, it is prone to problems such as oil leakage and tension cylinder damage. Therefore, it is obvious that the answer to this question is for difference.

Improve the service life of the tension cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the tension cylinder (such as the tension cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the tension cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the tension cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single tension cylinder exhaust.

Answers to some questions about tension cylinder:

Can the hydraulic oil in the cylinder return to the tank?
Yes, there is a way, for example, first remove the cylinder from the machine, and then connect the two pipes on the cylinder, so that the cylinder piston rod is completely retracted into the cylinder, at this time, the piston is with the bottom, and the rear chamber is almost no oil, and then screw off the joint at the end of the front chamber by the hydraulic station, and put it in an empty bucket. Finally, insert the gas pipe into the oil port of the rear chamber. Open the air source, and then the rod will run out, and you'll drain the hydraulic oil from the end of the rod, which requires a source of air on site.

The inner diameter of the injection cylinder is 203.2mm and the diameter of the screw is 63.5mm. What is the enhancement ratio?
Oil pressure multiplied by the cross-sectional area of the cylinder is equal to the theoretical output force value, and then multiplied by the efficiency of the cylinder is equal to the actual output force value, and the oil pressure can be calculated by inverting the value input.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
91无码热| 丁香五月加勒比| 久久综合久久久久88| 大鸡巴操麻逼| 爱欲爱综合网| 涩婷婷91一区二区五月天| 三级片午夜久福利| 欧美一区 第二页| 激情综合网激情五月网| 日本三级视频一本道电影| 熟女第一页一区| 97成人乱色小说| 日本不卡一二专区| 一级色情在线| 乌克兰在线一区二区三区| 中文字幕午码久久| 婷婷色人人| 欧美在线观看最新一区| 色影院久久| 国产欧美日本一二区| 亚洲人妻熟| 激情五月,激情性爱| 人妻久久34| 久久综合日本久久综合88| 黑人操日本女人尖叫声| 夜草国产免费| 中文字幕日韩有码国产一区二区| 色哟哟—国产精品| 天天操天天干天天怼天天日| 精品国产伦理电影三级片在线看 | 三级片AA久久久久久久| 99精品日本观看久久| 黑丝袜熟女人妻AV| 在线播放国产按摩服务| 精品电影久久久| 成人在线99| 九一视频成人一区| 日本一区二区三区久久| 日韩 欧美 日本| 丁香五月婷婷激情深爱!| 天天艹天天射天天射|