亚洲三区在线观看无套内射,日韩欧美电影91网,这里有国产视频,超级碰不卡视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tilting furnace hydraulic cylinder Sold to Tunisia

Release time:2023-11-08 10:37:03 Hits: Current position: Home > News

This article mainly introduces:

Tunisia hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

Tunisia tilting furnace hydraulic cylinder

(Tunisia tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

tilting furnace hydraulic cylinder are widely used in Tunisia,because of no need for deceleration device,long service life,smooth movement.So our company has designed tilting furnace hydraulic cylinder for customers from Tunisia.

Introduction to tilting furnace hydraulic cylinder:

When the oil pressure of the tilting furnace hydraulic cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

If it is found that the tilting furnace hydraulic cylinder lubrication is poor or the tilting furnace hydraulic cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the tilting furnace hydraulic cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the tilting furnace hydraulic cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the tilting furnace hydraulic cylinder center line. In this way, when the piston works in the tilting furnace hydraulic cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the tilting furnace hydraulic cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

tilting furnace hydraulic cylinder diameter, rod diameter, stroke determination: Choose national standards or other standards tilting furnace hydraulic cylinder, avoid the selection of non-standard size, otherwise the difficulty of processing and manufacturing costs will be increased. The length of the tilting furnace hydraulic cylinder guide is determined by the length of the stroke. Check the strength of tilting furnace hydraulic cylinder, piston rod, screw, etc. according to the working pressure or load. At the same time, working pressure, ambient temperature, working medium and running speed are also the key to selecting seals.

When the piston speed of the tilting furnace hydraulic cylinder is high, the steel ball of the check valve flows with the oil flow, so that the valve hole is blocked, and the tilting furnace hydraulic cylinder moves irregularly. Elimination method: Replace the steel ball with a cone valve or spool with a guide shoulder.

Answers to some questions about tilting furnace hydraulic cylinder:

Two cylinders have a reversing control, if the load of the two cylinders is not the same, how to ensure their synchronization?
The piston rod of the cylinder is required to extend synchronization: install A shunt collector valve or synchronous motor at port A of the direction control valve, and then connect the two outlets of the shunt collector valve to the rod-free cavity of the two cylinders respectively. It is required that the outlet of the diverter collector valve is connected to the rod cavity of the two cylinders respectively when the piston rod is withdrawn in synchronization. The synchronization performance depends on the quality of the diverter valve and the leakage of the hydraulic system.

What does the maximum output force of the cylinder piston mean?
The maximum output of the cylinder is related to the pressure of the hydraulic system that you link to the cylinder. For example, the rated maximum output thrust of the MOB 50 cylinder is 1.3 tons and the rated pressure is 7Mpa. That is, when the input hydraulic oil pressure of the cylinder reaches 7Mpa, the maximum output thrust of the cylinder is only 0.98 tons. When the input hydraulic pressure is only 5Mpa, the maximum output thrust of the cylinder is 1.3 tons. Because the pressure of the cylinder limit is only 7Mpa, if the oil pressure of the input system exceeds 7Mpa, the cylinder can not withstand the pressure burst, and it is damaged.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产欧美日韩图片一区在线| 男人色天堂在线| 刘玥在线播放一区| 入禽太深免费视频| 色av婷婷网| 国产精品日韩欧美一区2区3区| 伊人三级片大香蕉| 三级网站日本B一区二区三区| 欧美黑人在线黑白后入| 亚洲美女熟妇视频| 女同一区久久| 久久久精品国产亚洲 v麻豆| 久久精品射精免费看| 中日韩在线久久久| 人妻丰满久久久久| 嗯嗯啊啊啊啊好爽视频| 黄色一级久久久久久久久| 欧美日本一区4区不卡| 免费无码不卡成人AV| 人妻3p一区二区h| 18精品久久久无码午夜福利黑人| 小日本操逼的| 日韩 久久 蜜桃| 大香蕉欧美国产亚洲| 国产射精免费网站| 国产精品自拍视频在| 木下凛凛子亚洲一区二区| 欧日韩久久久久久久久久久久久久| 久久看视频| 日韩经典中文字幕精品素人| 日B真人视频免费三十分钟| 性感国产一区二区| 九九中文字幕九九| 国产精品久久电影久久| 极品美女一区免费视频| 天天射天天日大陆| 青久草国产一区二区| 久久毛片视屏| 国产日韩视频欧美视频在线观看| 大香蕉AV福利| 免费午夜福利网站|