亚洲三区在线观看无套内射,日韩欧美电影91网,这里有国产视频,超级碰不卡视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailplate hydraulic cylinder Sold to Switzerland

Release time:2023-11-10 08:35:18 Hits: Current position: Home > News

This article mainly introduces:

Switzerland hydraulic cylinder,tailplate hydraulic cylinder manufacturer,tailplate hydraulic cylinder

Switzerland tailplate hydraulic cylinder

(Switzerland tailplate hydraulic cylinder,produced by Hebei Hengyu company)

tailplate hydraulic cylinder are widely used in Switzerland,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed tailplate hydraulic cylinder for customers from Switzerland.

Introduction to tailplate hydraulic cylinder:

The coordination of the sliding parts of the tailplate hydraulic cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

The scar on the sliding surface of the tailplate hydraulic cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the tailplate hydraulic cylinder wall. Therefore, before installation, these scars must be fully repaired.

Disassembly tailplate hydraulic cylinder: When disassembly tailplate hydraulic cylinder, strictly prevent damage to the screw thread at the top of the piston rod, the screw thread of the tailplate hydraulic cylinder head and the surface of the piston rod. It should also be noted that the piston cannot be played out from the tailplate hydraulic cylinder.

tailplate hydraulic cylinder is the most important part of construction machinery, the traditional processing method is: broaching tailplate hydraulic cylinder block - fine boring tailplate hydraulic cylinder block - grinding tailplate hydraulic cylinder block. The rolling method is: broaching tailplate hydraulic cylinder block - fine boring tailplate hydraulic cylinder block - rolling tailplate hydraulic cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the tailplate hydraulic cylinder block is about 1-2 days, rolling 1 meter of the tailplate hydraulic cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the tailplate hydraulic cylinder increases by 25%. If the tailplate hydraulic cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality tailplate hydraulic cylinders, you must take the rolling production process. After the tailplate hydraulic cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

Answers to some questions about tailplate hydraulic cylinder:

How big gear pump need to use for 60*100 cylinder?
One cylinder size alone does not determine the size of the pump used. Choose the size of the pump, at least to know 1, the size of the load is how much, by the size of the load and the size of the cylinder and other conditions can be calculated the pressure required by the hydraulic system. 2. Speed of operation. From this speed and cylinder size, the required flow rate of the system is calculated. The relevant parameters of the pump can be selected by the pressure and flow rate to determine what kind of pump is required.

Why do two hydraulic cylinders lift out of sync?
There may be several situations (do not know the result of the equipment, may not be accurate) 1, whether the slow one is worn 2, whether there is air in the slow cylinder 3, if the two cylinders are supplied by the same oil port, whether the slow joint is blocked (some processing residue will reach a certain oil port under a certain coincidence condition, This situation will not happen if it is not necessarily good before) 4, the oil seal in the slow cylinder leaks, causing the feed oil to leak from the return oil end. Point 4 is most likely because it is invisible and a technical failure. If it is a dual oil feed (separate oil feed), it is also necessary to check the oil supply system and the oil return system (valve type).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
青青草一区二区三区费沁源| av久久青青草| 九九中文免费视频| 日本韩国久久综合网| r日韩成人午夜| 3P刮伦视频| 国产午夜青青操精品电影| 日本成人精品福利网站| 久久精品一區二區| 洗澡一区二区三区| 日本久久不卡网站| 这里只有99视频| 久久伊人影视| 天天干天天抽天天爽| 日韩大眯眯| 久久精品日产第一区二区三区广告 | 色噜噜一区二区三区欧日韩| 国产一区韩日伦理| 欧美精品在线国产| 91精品国产乱码久久久A片| 亚洲高清国产人妻激情| 中文字幕伦码在线| 婷婷五月天色AV| 亚洲欧美精品s图片| 久久精品日韩高清| 三级日本免费一区二区| 97伊人色色| 亚洲精品 69 久久 色婷婷| 99久久精品国产免费看不卡| 99热伊人| 久久综合九色综合欧美狠狠 | 色| 无码日韩大片| 无码一本道日韩欧美| 免费少妇久久| 欧美日本 熟女少妇| 啪啪啪全国免费| av中文网一起草| www.欧美日韩国产在线.com| 久久精品人妻中| 欧美亚洲国产一区在线看| 久碰精品|