亚洲三区在线观看无套内射,日韩欧美电影91网,这里有国产视频,超级碰不卡视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

steering power cylinder Sold to Thailand

Release time:2023-11-08 10:36:39 Hits: Current position: Home > News

This article mainly introduces:

Thailand hydraulic cylinder,steering power cylinder manufacturer,steering power cylinder

Thailand steering power cylinder

(Thailand steering power cylinder,produced by Hengyu Hydraulic Co., Ltd)

steering power cylinder are widely used in Thailand,because of excellent fatigue and impact resistance,long service life,no need for deceleration device.So our company has designed steering power cylinder for customers from Thailand.

Introduction to steering power cylinder:

When the steering power cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the steering power cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil steering power cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical steering power cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the steering power cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

How to determine the working pressure of the steering power cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, steering power cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

The internal leakage of the steering power cylinder should be prevented when the steering power cylinder is used. The internal leakage of steering power cylinder includes the leakage caused by excessive wear of steering power cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

If the steering power cylinder slips or crawls, please check whether there is astringency inside the steering power cylinder, because the internal parts of the steering power cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the steering power cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the steering power cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

Answers to some questions about steering power cylinder:

How to repair if hydraulic shears cylinder oil leakage?
The hydraulic cylinder is generally disassembled and the sealing ring is replaced. There are generally two ways to install the ends of the hydraulic cylinder. The larger hydraulic cylinder is mostly flanged disc type, which is screwed to the middle cylinder block by several bolts, the bolts are removed, and the cylinder head is slowly pulled out. The smaller hydraulic cylinder, the cylinder block and the head itself are threaded, and the rotating end cap can be removed from the cylinder block. If you do not understand the hydraulic cylinder, it is best to ask someone to deal with it. It is easy to damage the sealing ring and internal surface during disassembly.

How to distinguish the size of hydraulic cylinder cavity?
The hydraulic cylinder has a rod cavity and a rodless cavity. The rod cavity is the cavity that the piston rod extends out. The rod cavity is of course small due to the existence of the piston rod. That's just relative.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
夜夜燥久久| 最近久久久久最新视频| 狠狠躁日日躁夜夜躁2022麻豆| 久久久久久久一本| 久久久久久精| 中文字幕国产高清无码视频91| 白浆女同无码| 日韩一区和二区的差别| 国产l精品国产亚洲区久久| 欧美一区二区社区| 又紧又嫩又水又大又粗视频| 欧美大奶熟妇性交| 亚洲啪啪啪网站免费| 久久久久久久丫久久久极品| 久久久久教师一区| 欧美,日韩综合久久| 大香蕉视频91| 免费在线播放黄色AV电影网站| 国产美女私处操逼视频| 国产免费av地址| 国产一区二区麻豆久| www,91精品三级| 啊啊啊轻点插我啊啊啊视频| 国产夜色精品一区二区AV| 精品不卡一区二区三区不卡| 老熟一区二视频| 美女爱操B视频| 国产欧美日韩综一区| 在线 欧美 一区| 色婷婷综合AV一区| 八成人玖玖| 天天射天天爽天天干| 波多野42部无码喷潮在线观| 天天干女人免费视频| 妞干网亚洲| 好吊妞这里有精品一| 少女视频哔哩哔哩免费版观看| 日韩一二三在| 色情综合影音先锋在线视频| 午夜福利视频在线v| 久久久久久av电影av|