亚洲三区在线观看无套内射,日韩欧美电影91网,这里有国产视频,超级碰不卡视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailplate hydraulic cylinder Sold to Sweden

Release time:2023-11-08 10:36:39 Hits: Current position: Home > News

This article mainly introduces:

Sweden hydraulic cylinder,tailplate hydraulic cylinder manufacturer,tailplate hydraulic cylinder

Sweden tailplate hydraulic cylinder

(Sweden tailplate hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

tailplate hydraulic cylinder are widely used in Sweden,because of no need for deceleration device,long service life,smooth movement.So our company has designed tailplate hydraulic cylinder for customers from Sweden.

Introduction to tailplate hydraulic cylinder:

How the cavitation of the tailplate hydraulic cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the tailplate hydraulic cylinder, resulting in corrosive damage to the parts.

When the tailplate hydraulic cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the tailplate hydraulic cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the tailplate hydraulic cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the tailplate hydraulic cylinder can meet the requirements by grinding. However, the life and reliability of this repair tailplate hydraulic cylinder are not high.

When the tailplate hydraulic cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the tailplate hydraulic cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil tailplate hydraulic cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical tailplate hydraulic cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the tailplate hydraulic cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

If the seal of the tailplate hydraulic cylinder is softened and sticky, it may be that the seal is incompatible with the hydraulic oil or the nearby lubricating oil, replace the appropriate seal; If the seal becomes hard and loses elasticity, most of it is because the ambient temperature is too high (more than 80 ° C), make appropriate temperature insulation protection or replace the high temperature seal.

Answers to some questions about tailplate hydraulic cylinder:

What are the requirements for hydraulic cylinder assembly? ① The installation of the cylinder should be solid and reliable. In order to prevent the influence of thermal expansion, in the case of large stroke and hot working conditions, one end of the cylinder must be kept floating.② pipe connection shall not be relaxed.③ The mounting surface of the hydraulic cylinder and the sliding surface of the piston rod should maintain sufficient parallelism and perpendicality.④ The central axis of the moving cylinder should be concentric with the center line of the load force, otherwise it will cause lateral force, which is easy to wear the seal And piston damage. The greater the distance between the supporting points of the piston rod, the smaller its wear. For the hydraulic cylinder of the moving object, the installation should keep the cylinder parallel with the moving object, and the degree of non-parallelism is generally not greater than 0.05mm/m. ⑤The sealing ring should not be installed too tightly, especially the U-shaped sealing ring.

How many boom cylinders, bucket rod cylinders and bucket cylinders are there in a small single-bucket excavator?
one for bucket, one for forearm, only one piece for a small excavator under the big arm, two pieces for medium and large excavator.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
熟女偷拍区一| 久久人人综合| 日本一区高清免费| 成人黄片黄久久久久久| 国产一级啊啊啊啊片| 欧美图片一区二区三区四区| 成人精品人妻一区二区三区| 不卡一次二次三次视频| 日韩欧美激情黄片| 张开腿让男生捅免费视频| 日本亚洲中文字幕三| 日韩免费一区。| 欧美超级黄片| 亚洲欧美乱综合小说区图片区| 极品淫欲小少妇诱惑| 日韩有码一区牛牛| 欧美特黄一级大片视频| 国产V日韩V欧美| 日韩精品一区二区三区久久| 亚洲日韩欧美久久网站| 午夜精品电影网‘| 亚洲国产精品欧美在线观看| 久久综合日本久久综合88| 日韩av在线一区| 欧美日本一道A区B区C区| 草比视频污在线观看| 久久亚洲综合99| 天天有再黄的免费视频| 无码Av一区二区| 久久久中文字幕无码av不卡一二区| 国产欧美色一区二区三区| 日韩欧美au| 美女日逼视频日本| 日韩高清一曲二区| 欧久久久久| 亚洲图片综合精品| 亚洲国产精产国品一二三在观看| 欧美特色高清一区不卡| 中文字幕人妻一区二区视频观看| 日本久久婷婷五月视频| 午夜福利伦理片高清在线第8季|