亚洲三区在线观看无套内射,日韩欧美电影91网,这里有国产视频,超级碰不卡视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

series synchronous cylinder Sold to Puerto Rico

Release time:2023-12-18 10:57:15 Hits: Current position: Home > News

This article mainly introduces:

Puerto Rico hydraulic cylinder,series synchronous cylinder manufacturer,series synchronous cylinder

Puerto Rico series synchronous cylinder

(Puerto Rico series synchronous cylinder,produced by Hengyu Group)

series synchronous cylinder are widely used in Puerto Rico,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed series synchronous cylinder for customers from Puerto Rico.

Introduction to series synchronous cylinder:

When the oil pressure of the series synchronous cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

Disassembly series synchronous cylinder: When disassembly series synchronous cylinder, strictly prevent damage to the screw thread at the top of the piston rod, the screw thread of the series synchronous cylinder head and the surface of the piston rod. It should also be noted that the piston cannot be played out from the series synchronous cylinder.

series synchronous cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the series synchronous cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

The method of sleeve series synchronous cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the series synchronous cylinder can be significantly improved by rolling in the finishing of the inner holes of the series synchronous cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.

Answers to some questions about series synchronous cylinder:

How to design the guide sleeve of cylinder diameter 400?
The purpose of the guide sleeve is to guide and seal. Therefore, it is necessary to look at the speed of the piston rod, working pressure and radial force. High speed, medium pressure, no (or very little) radial force, with a Steseal. Low speed and heavy load, medium radial force, combined seal. High speed and heavy load, large radial force, sealed with DU sleeve + copper ring + combination. The combination seal must have a lubricating oil passage, and a seal must be added to the outside of the oil passage.

In a hydraulic system, a hydraulic pump has many hydraulic cylinders and hydraulic motors, and these executive components do not coordinate their actions with each other.
A load-sensitive variable pump can be used if these components sometimes need to work simultaneously and the power required is large. The required flow is distributed by the multi-way reversing valve, and the required flow and pressure changes are automatically adjusted by the hydraulic pump. Pressure reducing valves can be used for particularly low pressure circuits. Because you execute more components, the use of quantitative pump will cause a waste of energy, the system heat is large, not suitable.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
伦理一区二区三区国产| 夂久久{999| 唐山老熟妇| 亚洲成人色欲嫩草| 香蕉午夜福利影视| 91国产精品成人| 久久久精品中文字幕| 后入二区人妻| 日韩少妇精品影院| 亚洲中文字幕在线观看不卡一区| 日本高清无码一区二区| 日本播放一区二区三区超碰| 欧美日韩一区二区三区视频播放| 精品国产乱码一区二区三区麻豆| 欧美伦奸一级黄片| 91亚色网站| 99资源站中文字幕无码| 亚欧国产一区二区| 亚洲激情偷拍| 国产走光合集一区二区三区| 麻豆国产色情网站| 国产日本精品久久久久久久| 成人久久久免费| 天堂一区精品九九秘 91菁菁| 欧美日韩精品一区二区三区五区十区| 午夜福利大全| 国产亚洲精品无毛嫩逼喷水| 不卡中文字幕av一区二区| 又粗又深又猛又爽无遮挡| 午夜电影久久久| 香蕉久久精品| 国产.欧美.日韩.人人| 天天三区三区精品| 射操精品色五区| 老司机无码专区| 亚洲骚逼综合网| 免费成人五月天激情做爱视频| 人妻激情亚洲福利| 99国产一区一区三| 猫咪成人一二三四区日韩国产欧美| 亚洲天堂一区二区二|